DMX RDM - HOW TO USE |
![]() |
DMX Kanalpatching Individuelle Startadressen Durch die Aufsplittung eines Gerätes in einzelne Sub-Devices wird die Möglichkeit gegeben, jeden Funktionsblock mit individuellen Eigenschaften zu versehen. Die wichtigste Aufsplittung ist dabei die Möglichkeit, jedem Block (jedem Subdevice, also jedem einzelnen Relais) eine eigene DMX Adresse zuzuweisen. Damit ist man nicht mehr an den üblicherweise vergebenen Adressblock gebunden. Dabei gibt es zwei Möglichkeiten, eine Einzeladressierung zu erreichen:
Die Beispiele sind mit folgenden Controllern erstellt:
Bitte klicken Sie zum Vergrößern auf die Abbildungen.
|
DMX Slot Patching Individual start address settings Splitting up a device into individual SubDevices allows to assign each SubDevice its own properties. The most valuable feature is the possibility to assign indivudual DMX adresses to each of the SubDevices. Thus you are no longer bound by the usual DMX block addressing. There are two options to address the individual relays:
Descriptions are shown for these controllers:
Please click onto the images to enlarge
|
|||
![]() |
Relaismodule werden im Standardmodus (eine Startdadresse und ein Block von nachfolgenden Adressen für jedes Relais) ausgeliefert. Die Umstellung auf Sub-Device-Modus ist per RDM möglich. Dabei wird das Relaismodul virtuell in mehrere einzelne Einheiten zerlegt (ein 6-Kanal Modul in 6 einzelne Relais), von denen jedes dann eine eigene Startadresse bekommen kann. Bitte beachten Sie, dass die Einstellung über ein Adressboard dann nicht mehr möglich ist. Zudem unterstützen nicht alle RDM-Controller den Subdevice-Modus. |
With delivery, relay modules are set to standard mode by default. The can easily be reconfigured to SubDevice mode using a suitable RDM controller. This will split up the relay unit into individual blocks, with each block having its own start address. Usually, each relay is considered being a separate Subdevice. Thus a 6-relay module will be reconfigured as 6 individual Subdevices. Please note, that in Subdevice mode external address boards will not work. Also please note, that some low cost RDM controllers do not support Subdevices. |
||
Setzen Sie dann einfach die Startadresse wie gewohnt. Um Relais 2 ebenfalls auf Adresse 1 zu setzen, wählen Sie auch hier als Startadresse 001. Klicken Sie dann Subdevice 3 und setzen Sie dort die Startadresse auf 002, danach Subdevice 4 und ebenfalls Startadresse 002. |
Set the start address as usual. The assign relay 2 to start address 1 also, select address 001 from the dropdown list. Then select SubDevice 3 and set the start address to 002, the select SubDevice 4 and set start address 002 also. |
|||
![]() |
Relaismodule werden im Standardmodus (eine Startdadresse und ein Block von nachfolgenden Adressen für jedes Relais) ausgeliefert. Die Umstellung auf Sub-Device-Modus ist nicht erforderlich, wenn eine Adresszuweisung durch das interne Patching erfolgt. In diesem Fall bleibt das Modul als Block erhalten, die Rangierung kann innerhalb der verfügbaren Adressen (Startadresse bis Startadresse+5) erfolgen. Das Patching verwendet herstellerspezifische RDM Kommandos (CMSC). Bitte beachten Sie, dass nicht alle RDM-Controller diese Option unterstützen. |
With delivery, relay modules are set to standard mode by default. This mode can be kept when routing the individual relay adresses using internal patching. Thus the module will still be accessible as block having a common start address, but the indivial relay address range is limited to the rootn dice address range, which is startaddress to startaddress+5. Internal patching can be set using a manufacturer specific RDM command (SMSC). Please note, that some low cost RDM controllers do not support manufacturer specific RDM commands. |
||
Senden Sie einen GET-Befehl ohne Parameter. Es wird dann eine Liste mit den derzeitigen Adresszuweisungen ausgegeben. Das sind bei 6 Relais demzufolge 6 Einträge, stets beginnend bei 1. Im Folgenden werden wir dieselbe Konfiguration wie oben herstellen: Startadresse 1 für Relais 1 und 2, Startadresse 2 für Relais 2 und 3, Startadresse 5 für Relais 5 und Startadresse 6 für Relais 6. |
Issue a GET command without parameters to display a list of settings. For 6 relays, you will receive a list of 6 entries, beginning with relay 1. We will now set the same configuration as used above: start address 1 for relays 1 and 2, start address 2 for relays 3 and 4, start address 5 for relay 5, and start address 6 for relay 6. |
|||
Geben Sie diese Daten als Sendedaten ein und senden Sie ein SET-Kommando. Wiederholen Sie das für Relais 3: 0003 02 und für Relais 4: 0004 02 - beide werden von Datenslot 2 (also Startadresse+1) bedient. Relais 5 und 6 müssen nicht gesetzt werden, sie sind ja schon richtig. |
Enter these data as data to be sent and issue a SET command. Repeat this for relay 3: 0003 02 and for relay 4: 0004 02 - both relays will then be driven from data slot 2, which is startaddress plus 1. We do not need to set relays 5 and 6 since there are no changes. |
|||
Um die Gesamtprogrammierung zu prüfen, senden Sie eineut einen GET-Befehl ohne Parameter. Es wird dann eine Liste mit den derzeitigen Adresszuweisungen ausgegeben: Startadresse 1 für Relais 1 und 2, Startadresse 2 für Relais 2 und 3, Startadresse 5 für Relais 5 und Startadresse 6 für Relais 6. |
||||
![]() |
Relaismodule werden im Standardmodus (eine Startdadresse und ein Block von nachfolgenden Adressen für jedes Relais) ausgeliefert. Die Umstellung auf Sub-Device-Modus ist per RDM möglich. Dabei wird das Relaismodul virtuell in mehrere einzelne Einheiten zerlegt (ein 6-Kanal Modul in 6 einzelne Relais), von denen jedes dann eine eigene Startadresse bekommen kann. Bitte beachten Sie, dass die Einstellung über ein Adressboard dann nicht mehr möglich ist. Zudem unterstützen nicht alle RDM-Controller den Subdevice-Modus. |
With delivery, relay modules are set to standard mode by default. The can easily be reconfigured to SubDevice mode using a suitable RDM controller. This will split up the relay unit into individual blocks, with each block having its own start address. Usually, each relay is considered being a separate Subdevice. Thus a 6-relay module will be reconfigured as 6 individual Subdevices. Please note, that in Subdevice mode external address boards will not work. Also please note, that some low cost RDM controllers do not support Subdevices. |
||
Setzen Sie dann einfach die Startadresse wie gewohnt. Um Relais 2 ebenfalls auf Adresse 1 zu setzen, wählen Sie auch hier als Startadresse 1. Klicken Sie dann Subdevice 3 und setzen Sie dort die Startadresse auf 2, danach Subdevice 4 und ebenfalls Startadresse 2. |
||||
![]() |
Relaismodule werden im Standardmodus (eine Startdadresse und ein Block von nachfolgenden Adressen für jedes Relais) ausgeliefert. Die Umstellung auf Sub-Device-Modus ist nicht erforderlich, wenn eine Adresszuweisung durch das interne Patching erfolgt. In diesem Fall bleibt das Modul als Block erhalten, die Rangierung kann innerhalb der verfügbaren Adressen (Startadresse bis Startadresse+5) erfolgen. Das Patching verwendet herstellerspezifische RDM Kommandos (CMSC). Bitte beachten Sie, dass nicht alle RDM-Controller diese Option unterstützen. |
With delivery, relay modules are set to standard mode by default. This mode can be kept when routing the individual relay adresses using internal patching. Thus the module will still be accessible as block having a common start address, but the indivial relay address range is limited to the rootn dice address range, which is startaddress to startaddress+5. Internal patching can be set using a manufacturer specific RDM command (CMSC). Please note, that some low cost RDM controllers do not support manufacturer specific RDM commands, and some do not support CSMCs. |
||
Der e:cue Controller gibt keine Parameterliste aus; insofern können hier nur Eingaben gemacht werden. Im Folgenden werden wir dieselbe Konfiguration wie oben herstellen: Startadresse 1 für Relais 1 und 2, Startadresse 2 für Relais 2 und 3, Startadresse 5 für Relais 5 und Startadresse 6 für Relais 6. Geben sie wie folgt ein: |
The e:cue does not display the list of current settings. Thus it is only possible to make entries. We will now set the same configuration as used above: start address 1 for relays 1 and 2, start address 2 for relays 3 and 4, start address 5 for relay 5, and start address 6 for relay 6. Please enter: |
|||
![]() |
Relaismodule werden im Standardmodus (eine Startdadresse und ein Block von nachfolgenden Adressen für jedes Relais) ausgeliefert. Die Umstellung auf Sub-Device-Modus ist per RDM möglich. Dabei wird das Relaismodul virtuell in mehrere einzelne Einheiten zerlegt (ein 6-Kanal Modul in 6 einzelne Relais), von denen jedes dann eine eigene Startadresse bekommen kann. Bitte beachten Sie, dass die Einstellung über ein Adressboard dann nicht mehr möglich ist. Zudem unterstützen nicht alle RDM-Controller den Subdevice-Modus. |
With delivery, relay modules are set to standard mode by default. The can easily be reconfigured to SubDevice mode using a suitable RDM controller. This will split up the relay unit into individual blocks, with each block having its own start address. Usually, each relay is considered being a separate Subdevice. Thus a 6-relay module will be reconfigured as 6 individual Subdevices. Please note, that in Subdevice mode external address boards will not work. Also please note, that some low cost RDM controllers do not support Subdevices. |
||
Setzen Sie als Parameter 0001 und senden Sie ein SET Kommando. Klicken Sie dann Subdevice 3 und setzen Sie dort die Startadresse auf 0002, danach Subdevice 4 und ebenfalls Startadresse 0002. |
||||
![]() |
Relaismodule werden im Standardmodus (eine Startdadresse und ein Block von nachfolgenden Adressen für jedes Relais) ausgeliefert. Die Umstellung auf Sub-Device-Modus ist nicht erforderlich, wenn eine Adresszuweisung durch das interne Patching erfolgt. In diesem Fall bleibt das Modul als Block erhalten, die Rangierung kann innerhalb der verfügbaren Adressen (Startadresse bis Startadresse+5) erfolgen. Das Patching verwendet herstellerspezifische RDM Kommandos (CMSC). Bitte beachten Sie, dass nicht alle RDM-Controller diese Option unterstützen. |
With delivery, relay modules are set to standard mode by default. This mode can be kept when routing the individual relay adresses using internal patching. Thus the module will still be accessible as block having a common start address, but the indivial relay address range is limited to the rootn dice address range, which is startaddress to startaddress+5. Internal patching can be set using a manufacturer specific RDM command (SMSC). Please note, that some low cost RDM controllers do not support manufacturer specific RDM commands. |
||
Senden Sie einen GET-Befehl ohne Parameter. Es wird dann eine Liste mit den derzeitigen Adresszuweisungen ausgegeben. Das sind bei 6 Relais demzufolge 6 Einträge, stets beginnend bei 1: 01 02 03 04 05 06 Im Folgenden werden wir dieselbe Konfiguration wie oben herstellen: Startadresse 01 für Relais 1 und 2, Startadresse 02 für Relais 2 und 3, Startadresse 05 für Relais 5 und Startadresse 06 für Relais 6. |
Issue a GET command without parameters to display a list of settings. For 6 relays, you will receive a list of 6 entries, beginning with relay 1: 01 02 03 04 05 06 We will now set the same configuration as used above: start address 01 for relays 1 and 2, start address 02 for relays 3 and 4, start address 05 for relay 5, and start address 06 for relay 6. |
|||
Geben Sie diese Daten als Sendedaten ein und senden Sie ein SET-Kommando. Wiederholen Sie das für Relais 3: 000302 und für Relais 4: 000402 - beide werden von Datenslot 2 (also Startadresse+1) bedient. Relais 5 und 6 müssen nicht gesetzt werden, sie sind ja schon richtig. |
Enter these data as data to be sent and issue a SET command. Repeat this for relay 3: 000302 and for relay 4: 000402 - both relays will then be driven from data slot 2, which is startaddress plus 1. We do not need to set relays 5 and 6 since there are no changes. |
|||
Um die Gesamtprogrammierung zu prüfen, senden Sie eineut einen GET-Befehl ohne Parameter. Es wird dann eine Liste mit den derzeitigen Adresszuweisungen ausgegeben: Startadresse 1 für Relais 1 und 2, Startadresse 2 für Relais 2 und 3, Startadresse 5 für Relais 5 und Startadresse 6 für Relais 6: 01 01 02 02 05 06 |
To check the final programming, issue a GET command without parameters to display the list of settings: start address 1 for relays 1 and 2, start address 2 for relays 3 and 4, start address 5 for relay 5, and start address 6 for relay 6: 01 01 02 02 05 06 |
|||
![]() |
Weitere DMX-512 Produkthinweise:
zurück zur SOUNDLIGHT HOMEPAGE
Letztes Update: 14.11.2013 (C) SLH 1997-2013